Industrial Coatings, Patches, Repairs and Surface Preparation for KY,TN,IN and WV

Industrial Coatings, Patches, Repairs and Surface Preparation for Commercial Painting in Kentucky, Tennessee, Ohio & Indiana

SURFACE PREPARATION – STEPS & METHODS  for CLEANING AND DEGREASING:

All residue – traces of oil and grease and other contaminants must be removed before grinding or shot blasting.  Grinding and shot blasting without cleaning will only push contamination deeper into the porous concrete surface. Use oil and grease emulsifiers to clean thoroughly.  Stubborn or heavy residue areas may require repeated applications.  Only then will the surface be ready for Industrial Coatings or a Commercial Painting in Indiana & Kentucky

MECHANICAL PREPARATION:

Methods such as Shot and Sand Blasting, Scarifying, Diamond Grinding, Grinding/Sanding, Key Cuts and Water Jetting and Blasting are examples of effective means of mechanical surface preparation.

Below is a brief summary of these methods with features, benefits and limitations:

Shot Blasting,  The preferred method of mechanical preparation that strips thin coatings, cleans and profiles simultaneously.  It is suitable for large and small areas, delivers high production rates, dust free, dry and cost-effective.  The excess shot must be swept-up after blasting.

Scarifying Method uses metal or carbide disks that rotate at high speeds.  Levels uneven floors and edges of concrete. Removes adhesives and thick film coatings. Dusty, very slow and labor intensive. Leaves very rough profile only fit for high build coatings.

Diamond Grinding – Diamond bits are used to grind the surface.  Leaves a very smooth profile, ideal for thin film system applications. Low dust levels. Removes epoxies and urethanes. Slower than other methods.

Grinding/Sanding Prepares, cleans and abrades existing coatings for recoat and helps smooth aggregate floors. Is slow and labor intensive.

Key Cuts Masonry saw cuts/small grooves (approx.1/4inch deep) made around drains, doors and transitions.  These serve as anchor points for the epoxy system, limit sections of failure and reduce undercutting by chemicals.

Water Jetting or Blasting – Water sprayed at extremely high pressure (5,000-40,000 psi) with enough force to profile concrete, remove laitance, contamination and unsound concrete.  No dust is generated, tight spaces can be prepared and different profiles can be achieved.  Eliminates need for harsh chemicals.  Sufficient water source must be available, time required for thorough drying.

PATCHING AND REPAIR

Settling cracks – repair after the sealer is applied and before finish coating.  Expansion joints should be repaired and filled with epoxy after the coating system is in place.  When patching apply sealer to crevice to be repaired before applying epoxy patch.   This will enhance the bond strength of the patch.   Apply epoxy / aggregate mixture immediately after mixing – spread with trowel – grind off excess.  This process should be considered before any renovation or remodeling project is initiated or completed.

  • Water tower coatings and paints
  • Wastewater treatment coatings

  • Epoxy Floor Coatings

  • Rustoleum Polyurea
  • Metalic Floor Coatings
  • Polyaspartic Floor Coating
  • Zero VOC
  • Zero HAP
  • NeverWet
  • XIM – X-I-M
  • Krud Kutter
  • Anti-Slip Floor Coatings
  • Rust Prevention and Rust Removal

Industrial Coatings, Patches, Repairs and Surface Preparation for Commercial Painting in Kentucky, Tennessee, Ohio & Indiana

Rust-oleum Rustoleum, Industrial & Epoxy Coatings, Tank Linings / Commercial Painting in Louisville KY

National Painting & Coatings Company Supplying Protective Coatings For Massive Cleveland Innerbelt Bridge Project

Epoxy intermediate coating Macropoxy 646 provides high-gloss protection from harsh Northeast Ohio weather for vital city artery

A leading National Painting & Coatings Company Supplying Protective Coatings was chosen by Atlantic Painting (Oak Lawn, Ill.) to supply high-performance protective coatings for the Ohio Department of Transportation’s (ODOT) I-90 Innerbelt Bridge project. Coating work is now underway on the 1.8 million square feet of steel that comprise the westbound span over the Cuyahoga River. Reconstruction of the bridge, which opened to traffic in 1959 and is the main east-west artery into and through downtown Cleveland, is the largest project in ODOT’s history. The new bridge, which is north of the existing span, will be 4,247 feet long and stand 120 feet over the Cuyahoga River Valley at its highest point.   Tank Lining & Coatings Kentucky Indiana.

To give the bridge a high-gloss finish and protect the structure from the harsh Cleveland elements, Sherwin-Williams will supply Macropoxy 646, an epoxy intermediate coating, and HP DOT Acrylic Polyurethane, a high-gloss top coat in off-white, for the project. The company is also providing Zinc Clad IV organic epoxy that will be used by Atlantic’s field painters to touch up the shop-primed steel sections and splice plates. More than 26,000 gallons of coatings will be used for the project.

“ODOT needed high gloss, a low film build of 2-4 mils with higher-build performance, superior weathering, and ease of application,” said  regional market director, bridge & highway,  “These products will achieve all of those requirements. As a company headquartered for nearly 150 years in Cleveland, it is gratifying to be an asset protection partner on an infrastructure project that is such a vital link to the city from points near and far.”

Although not all states require steel bridges to be coated, ODOT does stipulate protecting its bridges in this manner.   Bridges in Northeast Ohio must stand up to some of the most rigorous inspections there are, given the constant expansion and contraction caused by thermal cycling, and exposure to road salt and airborne contaminants from Lake Erie winds.

The project design and product specifications address these issues. Because of the level of degradation and corrosion that can occur at structural joints, ODOT wanted to limit their number. The old bridge had joints at every one of the 14 piers, but in the new design there are only two.

In addition, QUV accelerated weathering tests (5,000+ hours of UV exposure is Ohio’s standard) and field experience document the superior gloss retention of the topcoat, which doubles the maintenance-to-recoat cycle. “Our testing demonstrates gloss retention even after 9,000 hours of exposure. This considerably extends the lifecycle of the coating and provides unprecedented value for the taxpayers,” he noted, saying the bridge would likely only need to be repainted two or three times during its design life of 75 years.

The project is unusual in several ways. ODOT used a value-based design-build approach (vs. design-bid-build) for the first time, to expedite the work and minimize disruption to both local motorists and those traveling between Chicago and the Northeast US.

In addition, the bridge’s architecture has distinctive delta-shaped girders that complement the Cuyahoga Valley topography without dominating it. The design teams that competed for the work were evaluated on their ability to deliver on not just cost and an ambitious schedule, but also on preserving the aesthetics that define this part of Cleveland’s landscape. The project was awarded to general contractor Walsh Construction in partnership with HNTB Corporation, the lead architectural and engineering design firm, and HDR, the independent quality engineering firm.

A global protective and marine coatings company that delivers smarter asset protection and unmatched service and specification support to its customers from 4,000 locations worldwide.  From alkyds to zincs, the company offers a complete line of time-tested, high performance  Industrial coatings, Commercial Paints and systems to combat corrosion, supported by the largest group of NACE-certified coatings inspectors in the industry.  Serving Kentucky, KY Indiana, IN West Virginia, WV and Tennessee, TN.

 Tank Lining & Coatings Kentucky Indiana

Rust-oleum Rustoleum, Industrial & Epoxy Coatings, Tank Linings / Commercial Painting in Louisville KY

Industrial Coatings for Kentucky, Indiana, Illinois, West Virginia, Machinery & Equipment Refurbishing, Renovating, Painting, Coating, Protective Sealants, Rust & Corrosion Prevention

Industrial Coatings for:

Kentucky, Indiana, Illinois, West Virginia and Tennessee

Machinery & Equipment Refurbishing, Renovating and Painting

Coatings, Protective Sealants, Rust & Corrosion Prevention

Today’s machinery and industrial equipment are equipped with sensitive electrical and mechanical components.  Structural Steel, Ceiling Beams, Plant & Factory Supports – Rust, Corrosion and Protection of Louisville Kentucky and Indiana.

While it’s easy to see how the appearance on a machine’s exterior is degrading, peeling or oxidizing, to prevent extremely accelerated wear and premature equipment replacements costs, it’s critical to give attention to the effects highly corrosive agents can have on the machine’s internal connections, engine compartment, and undercarriage.

Structural Steel, Ceiling Beams, Plant & Factory Supports – Rust, Corrosion and Protection can be a difficult undertaking to control, prevent and mitigate common corrosive agents from disabling and destroying equipment.  And while machines all have different jobs and operate in diverse environments, a protective coating will help shield every single one from harmful corrosive environments that cause equipment decay and breakdown, which leads to increased downtime, lost revenue and shorter machine life.

Waxes and polishes can prevent some corrosion, but they are not designed to cover every part of a machine (specifically internal) and they require regular polishing and buffing; time that mission critical equipment could be spending in the field.

The cost to coat a machine can provide a substantial return on investment. The coating materials and application are typically less than one percent of the machine cost, and new machine owners are able to capitalize the cost of coating.

A properly prepared and applied coating can provide many years of protection, generating significant cost savings in equipment maintenance and downtime.

Bottom line: by protecting your equipment today, you’ll be able to make and keep more money tomorrow.

 

Commercial Painting and Building Renovation deserves an experienced and specialized contractor

Howell & Howell offers a full complement of interior and exterior commercial painting and building restoration & renovation services:

  • Visual Rollout

  • High Traffic Rollout

  • Preventative/Reactive Maintenance

  • Re-branding Renovation

  • Wall Cover Removal/Installation

  • Faux Finishes

  • Front Facades/Pylon Signs

  • EIFS Restoration

  • Minor Substrate Repair

  • Wood Finishing

  • Graffiti Control

  • Power Washing

For questions or information regarding our Painting services please call (502) 491 – 7985.

Comprehensive solutions:

You benefit from complete solutions: professional specification design, consulting services and survey assistance.

Howell & Howell assists with your project in many ways including:  product recommendations and color choices.  Together we implement a painting program that best fits your needs.

  • Visual Rollouts: Add new color to interior features to increase traffic.

  • High-Traffic Rollouts: Rejuvenate existing locations by sprucing up the areas that receive the most traffic: fitting rooms, cash wraps, restrooms and entrances…. Studies show that a fresh appearance promotes increased traffic and sales.

  • Preventative Maintenance: Schedule a regular refresh program, and eliminate the time and money spent on unnecessary service orders.

  • Rebranding/Renovation: Re-image your brand, change your sinage, replace your fixtures…and enjoy increased traffic and sales as a result.

  • Woodwork/Laminate Refinishing: Make your old cabinets and trim look like new again and save up to 90% over the cost of replacement.

  • Ceiling Tile Restoration: Brighten up aged and discolored ceiling tiles for less than half the cost of replacement, with fast and long-lasting results

Howell & Howell Contractors is a locally owned and operated commercial painting contracting company, based in Louisville Kentucky.   A commercial painter, contractor and industrial coatings specialist.

For questions or information regarding our  Building Painting services please call (502) 491 – 7985.

Howell & Howell Contractors is a recognized leader in high quality industrial commercial painting and structural coatings for businesses, buildings and equipment throughout Kentucky and Southern Indiana.


Howell & Howell is a commercial painter and contractor specializing in the application of architectural and protective paints and Industrial coatings. From an office suit to a large commercial complex, one floor or many, Howell & Howell Contractors has the best solution for any size of your commercial painting project.  For questions or information regarding our Painting services please call (502) 491 – 7985.  Howell & Howell Contractors is also recognized as a leader in high quality industrial and structural coatings for businesses and equipment throughout Kentucky and Southern Indiana.

For Information and details concerning all aspects of commercial painting and home remodeling – please see the following websites:   http://gmrginc.com/  and www.remodelinglouisville.com.

Howell & Howell Contractors offers and is:  QP1 and QP2 Certified, PDCA, EPA Lead Safe Certified Firm, SSPC, TWIC, Farrow Wet Blasting, Hallo Wet Blasting, Sand Blasting, Historic Renovations & Preservation Specialist, Commercial Wall Coverings, Interior Building Wallcoverings, Commercial Coatings, USDA approved coatings, EPA RRP Certified, Floor and Aisle Striping

 

Farrow Wet Blasting – A Company and Contractor for Louisville, KY


 Versatility, Workplace Health

Safety and Environmental Benefits Immediately

Environmentally Friendly, Safe Surface Coating Removal and Cleaning System

This system is ideal for a diverse range of industries as it allows a single, versatile cleaning or blasting system to operate in a variety of applications from fine, easily damaged or detailed work to heavy blasting.

Farrow wet blasting has the best environmental and work place health and safety credentials available, utilising a 100% clean and safe media along with low blast pressures.

Dry sand blasting causes severe dust problems which in turn create significant health issues. Such systems should only be used in suitable blast enclosures. The media usage from traditional sand blasting techniques can be as high as 500kg per hour. With the remarkable Farrow System your media usage is reduced to as little as 30kg per hour, which, when mixed and absorbed with the small quantity of water, greatly reduces any environmental risk and simplifies clean up. This saves you time and money.

Traditional water blasters use approximately 20 litres of our precious commodity every minute. This water, along with contaminants from the surface being cleaned, is then dispersed in large volumes into our environment. The Farrow System uses as little as 0.5 litres of water per minute, dramatically reducing the clean up liability.

 

Consider All These Applications

The versatility of Farrow wet blasting will allow removal of surface coatings from most substrates including aluminium, timber, steel, fibreglass, rubber, brick, masonry, concrete, granite, marble, ceramics, terracotta, brass, plastic and in some circumstances has even removed ink from paper.

The portability of the system allows a unit to be manoeuvred into virtually any location further enhancing its versatility.

When it comes to cleaning, Farrow wet blasting is able to remove graffiti from any surface, remove rust and other oxidants from boats, cars, mining equipment, machinery, jetty pylons in marine parks, marine anti-foul and other substances such as old varnish from timbers, black tar, grime, mould, scale, soot and salts from any industrial or commercial applications.

Who Can Take Advantage?

Farrow wet blasting can be used safely within populated urban areas, remote mining sites, marine and industrial yards, making the process suitable for:

Marina operators, navy, army, air force, mining companies, a range of industrial services, transport companies, government authorities, city councils, railways, main roads, housing associations, builders, renovators, cleaning companies, private/residential sector and many more. The versatility of the system makes it an ideal basis for a small business.

In fact the diversity of Farrow wet blasting is such that no matter what surface coating removal or cleaning requirement you might have the Farrow System is likely to be a cost effective solution and it is 100% environmentally friendly and safe.

Howell & Howell is a commercial painter and Farrow Wet Blasting contractor specializing in the application of architectural and protective paints and Industrial coatings. From an office suit to a large commercial complex, one floor or many, Howell & Howell Contractors has the best solution for any size of your commercial painting project.  For questions or information regarding our Painting services please call (502) 491 – 7985.  Howell & Howell Contractors is also recognized as a leader in high quality industrial and structural coatings for businesses and equipment throughout Kentucky and Southern Indiana.  

Asbestos Removal & Abatement – General Information

Asbestos Removal & Abatement from

Commercial Buildings

Structures containing asbestos are marked.
Weathering of fibrous asbestos sheeting showing loose fibres.

A typical  asbestos enclosure.
Many buildings contain asbestos, which was used in spray-applied flame retardant, thermal system insulation, and in a variety of other materials. Asbestos was sometimes “flocked” above false ceilings, inside technical ducts, and in many other small spaces where firefighters would have difficulty gaining access. Structural components like asbestos panels were also used. In residences, asbestos was often a component of a type of flocked acoustic ceiling called popcorn ceiling or “cottage cheese ceiling”, until its production was banned in the U.S. in 1978. However, the ban allowed installers to use up remaining stocks, so houses built as late as 1986 could still have asbestos in their acoustic ceilings. The only way to be sure is to remove a sample and have it tested by a competent laboratory.

Depending on how and where asbestos was applied, it might not pose any risk to most users of the building. If the fibers cannot become dislodged, they cannot be inhaled, and thus the asbestos poses no risk.

However, some methods of applying asbestos, particularly flocking, allow asbestos fibers to gradually drop off into the air. Asbestos poses hazards to maintenance personnel who have to drill holes in walls for installation of cables or pipes.

Even if the workers are protected, such maintenance operation may release fibers into the air, which may be inhaled by others. Interventions in areas where asbestos is present often have to follow stringent procedures.

When asbestos fibers can easily be made into airborne dust, the material is known as friable. For example, a popcorn ceiling is extremely friable, whereas asbestos floor tile is considered non-friable.

Different countries have different regulations and methods of enforcement, when it comes to asbestos removal. It is extremely important to remember that prior to any asbestos removal procedures taking place; the client has a duty of care and must verify that the specialist removal contractor can provide the following: proof of license if licensing is required within the jurisdiction; proof of specific asbestos public and employer liability insurance; proof of worker training to include supervisor and contract manager training within 12 months; proof of worker fit-testing and medical surveillance, within 12 months; proof of specialist equipment testing within 6 months – DOP and PAT within the EU. Optionally the specialist contractor should be able to provide accreditation from ARCA or other such trade organization.

If removal is to be performed when users are still present in the building, it is usually necessary to relocate some users temporarily. Typically, the part of the building from which asbestos is being removed has to be sealed off in order to prevent contamination of the other areas. Methods of sealing off an area often include the use of Polyethylene film, duct tape and negative air pressure machines which are fitted with HEPA filters. The idea is that the contained area is pulling fresh air in as to not allow asbestos fibers into the surrounding environment.

Only a special vacuum cleaner that’s designed for asbestos containment (class H) can be safely used when cleaning up during and after asbestos removal. Ordinary vacuum cleaners cannot be used, even those fitted with a HEPA filter.   An ordinary vacuum cleaner will expel the asbestos fibres into the room air.

If the building is closed to normal users, it may be necessary to seal it off from outside atmosphere so that no accessible air is contaminated. Examples of asbestos removal enterprises include the Jussieu Campus (begun circa 1996 and still going on as of 2005) and the Tour Montparnasse (in 2005, projected duration was three years if the tower was emptied of its users, and ten years if it were not).

Removal is not the only means of asbestos abatement. Asbestos and asbestos-bearing materials may be “enclosed” or “encapsulated” to prevent building occupants from being exposed to the fibers.

An asbestos-containing building that is to be torn down may have to be sealed (see third picture on right), and to have its asbestos safely removed before ordinary demolition can be performed. The asbestos removal may take longer and cost more than the actual demolition. For example, the former seat of parliament of East Germany, the Palast der Republik, was stripped of most of its asbestos between 1998 and 2001, before it was finally demolished starting in 2006.

Other Terms Associated with the same subject:

  • Asbestos
  • Mesothelioma
  • Asbestosis
  • Asbestine
  • Asbestos and the law
  • Fibro
  • Fireproofing
  • List of minerals
  • Vermiculite

recognized as a leader in high quality industrial and structural coatings for businesses and equipment throughout Kentucky and Southern Indiana.

 

HPP specializing in the application of architectural and protective paints and Industrial coatings. From an office suit to a large commercial complex, one floor or many, HPP has the best solution for any size of your commercial painting project.  HPP, recognized as a leader in high quality industrial and structural coatings for businesses and equipment throughout Kentucky and Southern Indiana.


Our services, skills and qualifications include:  Asbestos Removal & Testing,  QP1 / QP2 Certified, PDCA, EPA Lead Safe Certified Firm, SSPC, TWIC, Farrow Wet Blasting, Hallo Wet Blasting, Sand Blasting, Historic Renovations & Preservation, Commercial Wall Coverings, Interior Building Wallcoverings, Commercial Coatings, USDA approved coatings, EPA / RRP Certified, Floor and Aisle Striping, Industrial Coatings, Water Tower & Tank Lining.